闪电联盟 - Powered by phpwind

在线pony8000

UID: 125

IT资讯组

发帖: 53735

今日发帖

最后登录: 2026-10-21

只看楼主倒序阅读使用道具楼主发表于: 2019-09-22 06:10:52

SynaptiCAD Product Suite 20.51| 294.6 Mb

SynaptiCAD was founded by electrical engineers to create design tools that helped engineers think critically about their designs. Being engineers themselves, they were frustrated by having to almost complete a design before being able to get simulation results. Our founders decided that there must be a better approach for interacting with design tools and from this simple idea they created SynaptiCAD, a company that creates "tools for the thinking mind". This idea permeates all of our tool interfaces.

With SynaptiCAD's tools you are able to begin analyzing and simulating design ideas right away without having to complete an entire circuit model or schematic. Our tools automatically handle many of the minor details involved in the design effort, leaving you more time to focus on the bigger picture.

SynaptiCAD based of the electrical engineers, in order to manufacture draft tools, which helped engineers to think of their drafts critically. Being implements blank, it frustrated, by a draft before in the situation its locks nearly must, results of simulation receive. Our founders decided that there must be a better approach for the effect on draft tools and from this simple idea it SynaptiCAD caused, a company rlt, which manufactures tools for the thinking understanding. This idea penetrates all our tool tools. With SynaptiCADs tools in the position you are draft to analyze and to simulate begin ideas immediately to lock without having, an entire electric circuit model or - diagram. Our tools treat automatically many of the small details, those into the draft effort along and leave to you more time to concentrate in the larger illustration.

Operating System: Windows 7, 8/8.1, 10

SynaptiCAD Product Suite 20.51新功能

项目级功能

Project Window中的New Port Mappings和Parm Mappings文件夹显示了测试模型如何连接到测试平台。此外，让用户更改映射。
Port Mappings图标颜色指示映射是默认映射（绿色）还是自定义映射（橙色）。在默认映射中，在测试平台中创建的信号与被测模型中端口的确切名称相匹配。当您想要测试诸如两个级联并行加法器电路之类的设计而不首先创建包装两个加法器的模块时，自定义映射会很有用。

BuHunter功能

tep Over和Step Into按钮将启动模拟器（如果尚未启动）。
GUI允许您在模拟完成后查询模拟状态，直到您按下红色“结束模拟”按钮。必须先按“结束模拟”按钮，然后才能开始新的模拟。
为GUI添加了模拟调用堆栈显示。这对于调试任务和函数的调用很有用。

时序图级别功能

在项目窗口中显示包变量以便于调试。
在“项目”菜单中添加了“导出时序图”，以将项目中列出的所有时序图导出为特定格式。此功能适用于WaveFormer Pro和DataSheet Pro。请参见第11.3节“导出一般说明”。
新的命令行选项-M将第二个时序图合并到正在加载的时序图（以前此功能只能从GUI访问，现在可以作为批处理操作执行）。
扩展VCD文件导入兼容性。

本部分内容设定了隐藏，需要回复后才能看到

关于激活

Place keyfile to installation dir.